Pressure Washer Solutions » clean

How to Clean Your Flat Roof

admin — Tue, 29 Jun 2010 05:00:07 +0000

There are three common methods to clean your flat roof. But, all of them have their pros and cons and accordingly you should find out which method is more suitable for your flat roof. Most of the roofs are stained by algae and require regular cleaning to keep them looking excellent. Your worries would have been multiplied with a roof with shingles. But as flat roofs mostly do not have shingles, there is no need to worry about them.

The largest problem with flat roof is of stagnant water after rainfall. Though most of the flat roofs are slightly slanted, which is of course not noticeable, yet water stagnates and becomes the cause of growth of moss and algae on it. If the moss or algae infected parts of your roof do not receive sunlight early in the morning then this algae does not die, instead it grows with the help of morning dew that has settled on your roof, further aggravating your problem of an unclean roof.

As said earlier, there are three ways in which you can clean your flat roof. A very common method is pressure cleaning. You can use a gasoline powered pressure washer. It delivers 2.4 gallons of water per minute and as a result releases a pressure of 2,500 pounds per square inch! You can equip the spray wand of the pressure washer with a 25-degree tip as used for general purpose cleaning. You can get astonishing results with this method of cleaning your flat roof.

All the dust, algae, moss and lichens that have covered your roof over a period of time will be removed. But, one thing to be kept in mind while using this method is that you should keep the spray wand tip close to the area to be cleaned, something like 6 inches from the surface. It is a very environment friendly way of cleaning your flat roof. It also saves you from investing your money in chemicals as required in other ways of cleaning your flat roof like chlorine solutions or sodium hydroxide base solutions.

Another way to clean your flat roof is with the help of chlorine solution washes. This procedure takes shorter duration to clean your flat roof. It requires much lesser time to rinse as compared to the other two methods. As a result the roof is saved from a lot of wear and tear due to prolonged hours of washing and cleaning. But, chlorine is toxic for some people and some plants as well. So care should be taken to keep them away when you are carrying out this procedure to save them from spray runoffs.

Another method of cleaning your roof is based on Sodium Hydroxide. Cleaners that have a base of Sodium Hydroxide are very effective as degreasers, but they need to be rinsed a lot as compared to chlorine solutions. This is not only time consuming but also involves a greater risk for your roof to be hurt. Sodium oxide is also toxic and should be kept away from coming in contact with property or persons. Plants should be especially kept away from Sodium Hydroxide. This chemical is also caustic and cause irreversible hurt to your roof if used in high levels.

How to Clean Your Flat Roof is a post from: Pressure Washer Solutions

How to Clean Your Wood Deck?

admin — Sun, 27 Jun 2010 02:18:06 +0000

A perfectly maintained wood deck enhances the look of a house and the general outdoor environment that surrounds it. Proper cleaning and staining of a wood deck will allow you to delight in it for many years. Whether youâre entertaining or enjoying silent times with your family, a properly maintained deck enhances any occasion.

Pressure cleaning is an efficient way to get your wood deck looking fantastic. Decks take a beating throughout the year, especially in climates where there are extremes in temperature and weather conditions. Wood decks face constant exposure to the elements. Sunlight, grime, dust and mildew, as well as animal and human traffic, constantly bombard a deck âs surface. On top of that, add the wearing effects of rain, ice and snow. All these things cause wood to break down and deteriorate.

All these factors can cause substances to become embedded in the wood. When it comes time to wash your deck, either as part of a general cleaning or to get it ready for staining, youâre likely to find it âs not an simple job. While common household cleaners may get rid of some surface dirt and grime, they canât do the heavy-duty cleaning that pressure washing can.

Reckon of what youâve seen accumulate on your wood deck. More than likely, youâve seen tree sap, bird droppings and greasy substances that have found a home on your deck. In addition, there are often rust stains from metal clasps, braces and nails. There is quite a buildup of residue on a wood deck âs surface. This is the case whether it âs coated or uncoated. Coated wood decks tend to lose their coating eventually and require refinishing as they accumulate dirt and stains.

The best way to get all of these unwanted substances off quick is to use a pressure washing system. A quality power washing apparatus can save you time and money. The force of the water action, concentrated to provide maximum cleaning power, means you get the job done quicker. The water pressure does the nitty-gritty work, so you donât have to use expensive de-greasers or other cleaning agents as much, if at all.

Pressure washing provides the optimally clean surface condition that is needed before you can stain your wood deck. Staining provides increased protection from the elements, but there is no use attempting to stain your wood deck if it still has dirt and other harmful residue. When you stain wood that is still dirty, you trap damaging particles on it. This causes it to deteriorate as these particles continue to infiltrate the wood under the stain coating. Power washing eliminates unwanted substances so your staining solution covers an ultra-clean surface. This makes your deck âs end appear attractive and vibrant.

Pressure cleaning of a wood deck is a wise alternative to scrubbing with corrosive cleansers. Many cleansers can themselves cause wood to wear and have a dull look. Power washing can do a job quickly and thoroughly, leaving the original wood free of harsh chemicals and abrasives. When you use a power washer of proper pressure for the size and type of your wood deck, you are using a powerful solution for getting stubborn stains out.

A quality power washer with a wide fan tip works well on wood decks. The wide fan tip will promote even spraying, which is safer for wood fibers. A excellent pressure washing system will get rid of mildew, fungus and penetrating dirt that cause wood to break down.

When you clean your deck, consider a pressure washing system. Its focused, powerful cleaning action can eliminate the need for detergent. That makes power washing environmentally friendly and efficient at the same time. With pressure washing, you have an immaculate looking deck. And because power washing is quick, you have more time to spend enjoying that gorgeous deck.

How to Clean Your Wood Deck? is a post from: Pressure Washer Solutions

AR North America Inc. AR383 Blue Clean Pressure Washer Reviews

admin — Thu, 24 Jun 2010 02:21:12 +0000

A powerful 1900 P.S.I. electric pressure washer for residential use. Features: Rated flow 1.5 GPM, aluminum pump, automatic start stop when trigger is pulled and released, universal copper winding motor, 38′ power cable, plastic gun lance, 18′ hose, hose reel, quick coupling gun hose machine, rotating lance, adjustable spray nozzle, and foam sprayer. Use to clean sidewalks, driveways, decks, fences, patio furniture, vehicles, and other small household projects. Optional accessories available from vendor.

Technical Details

-1900psi pressure washer
-A powerful 1900 P.S.I. electric pressure washer for residential use
-Features: Rated flow 1.5 GPM, aluminum pump, automatic start/stop when trigger is pulled and release
-Use to clean sidewalks, driveways, decks, fences, patio furniture, vehicles, and other small househo
-Optional accessories available from vendor.

Customer reviews

“Ok for consumer grade”
By Solomon B. So
Pretty much what I expected from a consumer grade power washer. The hose connectors are very flimsy and I doubt the PSI rating is within 500 PSI of it’s claimed ratings. Had a Karcher pressure washer before with a rating of 1200 PSI and it is about the same.

“Exellent product, even better customer service.”
By Tony Suslovich (New York, NY)
The pressure washer does its job perfectly. It has a really long electric cord which was one of the requirements for me since I didn’t want to mess with extension cords. The hose is really pretty long too, so you don’t have to drag the pressure washer around when you wash your car for example. Just set it in one place and the length of the hose will be enough reach all around.
The pressure washer comes with 2 wands. One has a rotating tip and the other one has a tip that can be adjusted for different spray angles so you don’t really need to buy any extra tips. It also has a bottle for cleaning chemicals.
All accessories, electric cord and hose have their place right on the unit and they fit silent nicely.
Don’t forget, it has 1900 PSI which is really pretty high pressure for non-commercial pressure washers. I don’t know what’s inside the unit, but it just feels sturdy and solid.
I don’t usually write reviews but what made me do it is AR North America’s customer service. After testing the unit, I ordered an extra accessory from them directly (flat surface cleaner to clean cement surfaces). They have phone #’s and email addresses of their entire staff listed on their web side, so I questioned few questions which were answered immediately. So I placed my order and couple of days later they informed me that the part I ordered was on back-order, so they offered to refund the money if I didn’t feel like waiting. You know, usually companies will make you wait even if it’s couple of weeks. I questioned them how long I’d have to wait and they told me about a week which wasn’t a huge deal for me at all, so I was prepared to wait. The next day I received another email from them saying that they would send me a surface cleaner instead of one I had ordered…get this… at no extra charge. I buy stuff on-line very often and I have never seen anything like that before.
Fantastic product, fantastic customer service. It’s very comforting to know that a company stands

See more : Electric Pressure Washer , Electric Pressure Washer , Gas Pressure Washer

AR North America Inc. AR383 Blue Clean Pressure Washer Reviews is a post from: Pressure Washer Solutions

The Creation Of A Plant To Clean Concrete Pressure Washer

admin — Mon, 21 Jun 2010 05:00:05 +0000

Maximum efficiency in the cleaning and the aerospace industry is a key to the survival and higher incomes. The trailer or tuck the device must be set so that you have a garden hose and use of water outside, because you never know when you need a type of cement or other jobs. A new structure should also be quick release from the tank and the intake manifold of the pressure washer. It should also be a valve, which is activated so that the water flows outblack tank that now holds the water outside, if you arrive with a hot water pressure washer skid unit unchanged with a tank float.

There must be a connection to a water pipe that is on top of the tank black. The interior of the container is a swimmer in water so that if you do not press the shutter button and the location of water. When cleaning concrete always PSI 3000 + and + 180 degrees water. These two elements are essential for cleaningConcrete efficiently and properly.

Now we talk of chemicals for one minute. To clean the rust, it is a product made by Simonize, which can be ordered by Howard Pressure Washers AAA Arizona, which means “Concrete Cleaner and Etch. Delco Cleaning Systems of Texas is a different chemical substance, which works quite well; http://www.DCS1.com. This substance is an acid and can be very perilous, but certainly work well. In this chemical, you can do with a metal hand-held shower spray instead applyBasket. If using a syringe, the plastic parts of it, the syringe, at least not more than one or two times before breaking up the pieces, and it is useless. The chemical must be mixed with water 50-50. If you search on colored concrete, do a patch test first, because it takes a bleaching agent and so relieved, it might be simpler than the original concrete.- Garden hose storage

Removal of oil stains or grease can be used Simonize SC 260 is a type of chemical pellets that looks like cat litter. ToYou must apply wetland will be covered first and then spread a thin layer of it on the spot. Take a brush and shake for the work inside Let it remove some fifteen or twenty minutes before you. Make sure you are removing the granules. The chemical should be next for emergencies, if possible, be used. This stuff is very thick and use a brush with long bristles, which are applied to the roller glue. Allow for fifteen to twenty minutes, thenremove it to be very careful not to get on you or any of the other chemicals in this matter.- Garden hose storage

To view the most efficient use of time to a specific development site of a person should lose debris swept from the working area, while the other body of the device. Be sure that all corners are too sweeping, because this is the most to lose in the dirt seem to end. I remember that when you rotate a zone Hydro are simply the removal of dirt and stains. Need newareas around the garbage out from the concrete to go. After the twister hydro the area that you cover all the metal parts or whatever works best for you and go with the hand wand all the distress spots and the outer covering of concrete must be used. READ MORE http://www.gardenhosestorage.goodarticlesite.com/the-creation-of-a-plant-to-clean-concrete-pressure-washer/

The Creation Of A Plant To Clean Concrete Pressure Washer is a post from: Pressure Washer Solutions

What You Want To Know About Steam Clean Pressure Washers

admin — Sat, 29 May 2010 02:17:33 +0000

Pressure steam cleaners are machines that clean surfaces using steam or hot water. The steam and the pressure behind the machine provide a very efficient way of removing dust mites, allergens, mold, fungus, and bacteria. This is the preferred way of cleaning in such places as hospitals, restaurants, pharmacies, and hotels. In the traditional sense, steam cleaner pressure washers are composed of a boiler, a collecting tank, a hose and brushes. Hot water is sprayed under pressure on the surface being cleaned.

The amount of pressure that you need or the flow rates are what will likely direct you to the machine that you will eventually buy. The flow rate is the amount of water that you will be able to use to remove the debris. The pressure expresses how hard the water will approach the surface of what is being cleaned. When you are cleaning flat surfaces it is more vital to have a high rate of flow as that will make it much simpler to loosen, remove, and wash away the debris. When you are cleaning surfaces that are not flat or that might be vertical, pressure would be more likely what you would be interested in.

These units have advanced quite nicely and are more affordable than you may reckon. There are various styles and accessories that are available for power steam cleaners. Steam cleaner pressure washers are available in gas powered or electric powered capabilities. Obviously the gas powered versions are more portable and less constricting which is convenient for outdoor work. They are also more likely to offer a longer life expectancy with less repairs needed.

The electric powered steam pressure washers are not vulnerable to wet conditions and while they can be used outdoors they also can be used indoors as well. The gas powered steam cleaner pressure washers can not be used indoors as they omit carbon monoxide. Another benefit of the electric version is that it makes much less noise.

Commercial pressure washers and industrial steam cleaner pressure washer’s offer much more industrial equipment than pressure washers designed for use in the home. Many commercial users use poor judgment when buying home pressure washer machines because they are much cheaper. The problem is that they will never last as they are unable to endure the industrial workloads.

Steam cleaner pressure washers depend upon heating coils that reach temperatures past 300° F, and are much better than either cold or hot water pressure washers in regards to removing grease, dirt, concrete stains, food, chewing gum, unsightly graffiti, and numerous other types of debris. Stainless steel or heavy carbon heating coils are most reliable and also help with making the right environment and ultra high temperatures that are needed.

Another perk of steam cleaner pressure washers is that they do not rely on chemicals like cold water pressure washers do. The high steam pressure that is omitted is brilliant to clean better than hot water and cold water pressure washers. The method of powering a pressure washer is every bit as vital as the heating method.

What You Want To Know About Steam Clean Pressure Washers is a post from: Pressure Washer Solutions

Power Pressure Washers Buying Tips – What, Where and How Often Do You Clean?

admin — Fri, 21 May 2010 02:18:58 +0000

Power Pressure washers have become a very common sight for household users, and there are an entire range of machines with different levels of PSI cleaning efficiencies to meet all your cleaning needs, all from light weight cleaning to intensive challenging task for your pressure washing business. To get the right power pressure washer, you need to know what you are cleaning, where you are cleaning, and how often do you clean.

Armed with this knowledge, you would then be able to narrow down your choice more efficiently. Cleaning a home and cleaning a commercial site demand very different types of power pressure washers to do the job. For commercial business use, you need more powerful units capable of blasting away industrial grim and harden grease, hence requiring units with higher PSI or pounds per square inch pressure power. Hot water models are preferred for more effective cleaning.

Conversely, for home use, cold water models will suffice, and the benefit of this is that they cost less as well as use less fuel compare to the former. Knowing where you need to clean is also a driving factor to your choice of machine. Take for instance if you need to clean up your summer lodge in the middle of the woods where AC power is unreliable at best, it is advisable to choose diesel or gas powered pressure washers instead of the electric versions.

But, be warned that diesel or gas powered pressure washers can only be used outdoors. You cannot use them indoors especially in terribly ventilated space as the carbon dioxide emissions from the machines could be fatal. In answering to the question of how often you do you clean, you would be able to derive a clear indication of the type of machines required.

If you need to do weekly household cleaning, get a reliable machine and value for money. If you are running a pressure washing business, then it is advisable to get commercial machines for extended usage. Knowing your cleaning needs will greatly help guide you to ultimately find the right power pressure washer, be it for household use or for your pressure washing business.

Power Pressure Washers Buying Tips – What, Where and How Often Do You Clean? is a post from: Pressure Washer Solutions

Why It Is Important to Pressure Clean and Seal Your Concrete Brick Pavers

admin — Sun, 13 Dec 2009 01:53:35 +0000

Having a brick paver patio, driveway, or pool deck is a fantastic thought because the brick pavers age perfectly and will not be out of style. It will seem like even a better thought with the small maintenance they require. It is recommended to at least once a year pressure clean to get rid of ancient stains and dirt, and to have a better result it is also recommended that you apply a coat of sealant. Although pressure cleaning is an extremely efficient way to clean your outside surface, and it can be used in nearly any kind of surface, you should watch out for some tips when hiring a company for the job. Remember, it might seem simple to do it yourself, but if you do not do the procedure correctly, you might hurt your surface as well as your plants and yourself. For instance, the right tip and chemicals are very vital to having a fantastic result. Also, the heat of the steam will be able to remove mostly all of the stains you have in your concrete brick pavers, and the water is not damaging to the surface. Not only that, the heat of the steam will also kill the bacteria and germs that cause your brick pavers’ surface to be dirty. By pressure cleaning your exteriors you will be giving it a welcoming feeling, as well as increasing the paver’s life. Keeping a nice looking exterior will also increase the value of a home/office from 5 to 10 percent! Pressure cleaning is considered the most inexpensive way to clean your exterior surface, and the only way to do it is using pressure washer. After pressure cleaning your concrete brick pavers it is recommended to seal it, too. Applying a coat of sealant is vital because it will avoid dirt, oil, and grease to getting inside the bricks. Since concrete brick pavers are some kind of spongy material it can be hurt by any type of debris, and the sealer will protect your bricks from them. Also, if you want to protect your surface from the humidity from getting to the pores, a coat of sealant is just what you need. It will also protect the concrete brick pavers from losing its color with time, extending its life and excellent looks as well. Even if the pavers were exposed for many years to the weather and all the debris, a excellent pressure clean and seal will enhance the look and extend its life. Pressure cleaning and sealing your concrete brick pavers is recommended once a year. It will protect your surface, enhance its look and extend its life. It will also make it very simple for you to maintain it clean yourself, and contrary to what many people reckon, it does not make your surface slippery because it gets inside the surface in order to protect it.

Why It Is Vital to Pressure Clean and Seal Your Concrete Brick Pavers is a post from: Pressure Washer Solutions

How to Maintain and Clean Your Parts Washer

admin — Thu, 19 Nov 2009 02:07:38 +0000

A washer works hard to ensure that parts come out clean and ready for the next production process. To keep the machine working at a high level, it must be cleaned on a regular basis. The contamination removed from the parts does not magically disappear; it builds up in the tank and can greatly reduce performance. Performing a tank and system clean out is an vital part of the routine maintenance a washer requires.
To start the process, turn off the automatic water fill supply and remove the nozzles and filters for cleaning. Pay attention to the direction spray angles of the nozzles in relation to the flow of the parts through the washer. Most nozzles will have an indication, either a slit or indented line, which shows the angle. It will be vital to replace the nozzles in the right position.
After the nozzles and filters have been removed, add a washer cleaning chemistry to the current wash solution. Heat the new solution to 160F, or the highest level attainable. Turn on the pumps and let them run for 30 minutes.
Clean the sludge that has been removed during this process and replace the nozzles. NOTE: If you run the pump for an extended period without the nozzles, then the pump motor will not sense the appropriate back pressure and the pump will burn up. After replacing the nozzles, turn the pumps back on and let them run undisturbed for 4 to 8 hours and allow the solution to work on the tank. Once the time is up, pump or drain the solution from the tank.
Now that the solution is gone, remove the shed sheets. There are 1-2 of these flat metal sheets, and they are located below the conveyor that covers the tank in the majority of machines. The sheets normally will have a #-20 stainless steel bolt in one of the corners. Remove the bolt and allow the sheets to be went forward or backward to gain access to the inside of the tanks. Also remove the marine clean out door on the side of the machine. Be careful not to hurt the door during this procedure. If a seal is torn or hurt, replace it before the machine is refilled. Once these are went, clean out any sludge, debris, or sediment from the tank bottom and sides.
Use a power washer to completely clean the interior of the machine, beginning at the top and moving down. Make sure to clean the heater elements, auto-fill valve, wash headers, and blow-off headers. Check all corners or other areas that could catch dirt.
Completely clean any oil removal devices, and flush the tank of the remaining dirty solution. Then remove the clean pump inlet screen and chip basket for cleaning. Wipe down the outside of the machine. Take some time to inspect the interior and exterior components of the machine for hurt or missing parts. Make notes of any hurts or problems for repair.
Replace the shed sheets and the clean out doors, making sure that the doors are in excellent condition before doing so. Replace the doors in the reverse order from how they were removed, and then replace any other devices that were removed from the machine during cleaning. Place the nozzles back in their original position, making certain that they are at the right angle and aim.
Refill the tank with a new solution of cleaning chemistry, and turn on the heat. Observe this process to make sure everything is running smoothly. Run the pumps and observe the gauge readings, making sure there are no more than 10-15PSI differences before filter and after filter. If there is, replace the filter.
Once the solution has reached the right temperature, check the spray pattern on parts moving through to ensure the machine is running correctly. Remove the wash door, using a piece of Lexan the size of the door, and observe. If it is right, replace the door.
Performing this maintenance on your washer will help keep it running efficiently for a long time. Cleaning out the debris and inspecting the main parts of the washer allow you to head off major maintenance problems before they become too large of a problem to deal with. The shut down in production time that will take place during cleaning is more desirable than the extended shut down which will inevitably occur if cleaning is not performed and maintenance goes unchecked.

How to Maintain and Clean Your Parts Washer is a post from: Pressure Washer Solutions

Rahsco RK-43 Series Frame Hot High Pressure Power Washers from Delco Cleaning Systems of Fort Worth

admin — Tue, 20 Oct 2009 00:37:01 +0000

Rahsco RK-43 Series Frame Hot High Pressure Power Washers from Delco Cleaning Systems of Fort Worth Include the RK-41, RK-42, RK42CL, RK-43, RK-43C, RK-45H, RK-45HC, and RK-8300. Flow range is from 4.8 to 8.7 GPM at 3,000 to 3,500 PSI at 200°F. Engines are 16 & 18 HP Vanguard, and 20 & 24 HP Honda with electric start.

On all 2009 Model Gasoline Engine Power Hot High Pressure Washers will include the following upgrades:

Featuring EBP™ Enhanced Burner Protection™

- Burner Power Light
- AIP™ Advanced Igniter Protection™ safeguards against:
- Electrical Failure, Engine Failure, Low Voltage
- Fuel/Water Separator Protects against
- Water and Debris in the burner fuel

Advanced Diagnostics Protection™

- Diagnostics Lights: Heater Fuel Solenoid, Pressure Switch, High Temperature Switch
- Thermal Pump Shutdown with Override Switch

On specific models all of the above features plus:

Enhanced Pump Protection™ with automatic clutch operation for extended life and reduced maintenance.

5-Year Limited Warranty

Compliments of Delco Cleaning Systems of Fort Worth at 800-433-2113, email: delco@dcs1.com , www.dcs1.com , or www.pressurewash.com .

Duration : 0:10:54

[youtube tX-mfoJ7LfQ]

Rahsco RK-43 Series Frame Hot High Pressure Power Washers from Delco Cleaning Systems of Fort Worth is a post from: Pressure Washer Solutions

Clean Your Homes Siding With A Pressure Washer

admin — Mon, 12 Oct 2009 01:26:48 +0000

Pressure washing which is also referred to as power washing is the best way to clean your house of mold and mildew. It is also a must to prep your home for painting and other projects. Basically pressure washing a house’s exterior will clean dirt and build up from the atmosphere off your siding material. One thing to be careful about is when pressure washing a house is not the same as a drive way. Only low pressure (around 300 psi) should be used. A high pressure spray will hurt the siding material. Your first question to a pressure washing contractor should be ‘what pressure do you clean with’. If they use high pressure (more than 300 psi), drop them like a hot potato! If you will be doing the job yourself, be sure your pressure washing unit has a house wash tip with it. If you plot on getting a new coat of paint on your house, it is essential to get the house washed. This will make a clean foundation for the paint to adhere to. Pressure washing

Clean Your Homes Siding With A Pressure Washer is a post from: Pressure Washer Solutions